How to Install Decals/Banners
If you are new to this process we recommend seeking professional installation – improper installation or use of the product will not warrant replacements or refunds. Successful installation and a long-lasting banner will depend on the weather conditions, temperature at the time of application, and proper surface prep. Ideal temperature range for installation is between 59°F–77°F (15°C–25°C).
- If you attempt installation at temperatures below 50°F (10°C) the vinyl can become brittle and harder to work with, resulting in premature peeling. Please be aware the adhesive takes a minimum of 24 hours to fully cure, thus overnight temperature drops and accumulation of condensation may cause the banner to peel.
-
If you attempt installation at temperatures above 77°F (25°C) have been known to cause the vinyl to become over-stretched and difficult to work with. Heat helps vinyl to become more soft and workable, but too much heat can easily result in irreparable tears and creases.
All colors are suitable for wet application, except for decals with white wax backing, oil slick/holographic/shiny rainbow material (these will require dry install only). The wet method is the easiest. It would be ideal to install your banner to a cool windshield in the shade. DO NOT install in direct sunlight. Avoid installing during high winds, sub-zero temperatures, heatwaves, rain etc.
-
Top layer is a sticky transparent layer called transfer tape.
(This keeps your decal/sticker together until it is applied) -
Middle layer is your actual decal.
(This is basically sandwiched between your transfer tape and wax backing) -
Bottom layer is the wax backing.
(protects the adhesive until the decal is ready to be applied)
INSTALL INSTRUCTIONS
Read carefully first before installing
- Prep the window with isopropyl alcohol and a microfiber cloth. Allow to dry. DO NOT use any dedicated glass cleaners - most are ammonia-based and leave a residue on the surface, causing the banner to peel and bubble over time
- Scrape over the surface of the decal with the Application Squeegee Tool for easy install to assure the decal is adhered to the top clear sticky transfer tape.
- (Optional and recommended for large decals/banners) Use masking tape to pre-align the decal, this may help especially if you have cut in between "Street" and "Animals" and have two pieces to align. Take a step back to make sure it's straight and where you want it.
- Carefully peel the bottom transfer tape layer from the top sticky transfer layer, ensuring the decal sticks to the top sticky transfer layer. Go slow, take your time so you don’t tear any letters. Don’t be afraid to bend the bottom transfer tape to encourage the vinyl to stick onto the top sticky transfer layer. DO NOT touch the adhesive decal backing, your fingers oils will prevent the decal from sticking.
- WET Application Method: For any color decal/banner EXCEPT oil slick / holographic / rainbow material and white wax backing. Mix 1 drop of dish soap per 32 oz of water in a spray bottle and lightly spray the back of the vinyl with the soapy water. Generously spray the windshield and surroundings with the soapy water to prevent the banner from sticking. Place down your decal and freely slide it to where you want it. Scrape from the CENTER-OUTWARD to squeeze out any soapy water and water bubbles from under the vinyl.
- DRY Application Method: For any color decal including oil slick / holographic / rainbow material. Carefully line up your decal and gently place down and apply section by section not all at once so the decal remains flush to the surface with no wrinkles. Scrape from the CENTER-OUTWARD, ensuring there are no air bubbles under the vinyl.
- Large sun strip banners only: Use a razor to gently cut the excess vinyl from around the edges of your windshield. Be careful not to scratch your paint.
- Allow the banner to dry and cure before exposing to weather, heat or wiper blades. Slowly remove the top layer transfer tape after 48 hours by pulling straight back against the glass, not up. This will leave your vinyl adhered and intact. Make sure no part of the decal remains on the transfer tape.
Note: If there are small air bubbles, they will disappear after a few days in the sun. Larger air bubbles can be smoothed down by poking a small pin hole and releasing the air. Small water bubbles may take up to a week to evaporate/disappear. If any edges of the decal lift you can use an Elmer's glue stick on the back side to secure it back down.
Thank you for representing Street Animals